Showing posts with label Dowel-Filling. Show all posts
Showing posts with label Dowel-Filling. Show all posts

Sunday, 12 July 2015

Jeremy's Mahogany LP: Headstock and Tuner Holes

This week, I finally got some more time to get back to Jeremy's Mahogany Les Paul build. Before I can start sanding this bad boy, there are a couple of modifications needed to support Jeremy's hardware choices. First and foremost, the existing tuner holes need to be reduced in diameter to support the 8.5mm tuner bushings to be found on his awesome Kluson tuners.

The first step in the process was to fill the existing tuner holes with dowel. Using some 12mm hardwood dowel from Bunnings, I reduced it down to around 11mm using 80 grit sand paper, then cemented it into the existing holes with Titebond. 

Dowel plugs sanded down from 12mm to fit
Once the glue was dry, It was a matter of using the dremel to roughly sand each plug down flat wth the headstock, and then filling around each with a little Timbermate. The result was one completely smooth - although kinda shitty looking - headstock.

Plugs glued in. Some sanding will be required!
Plugs sanded flat and the edges filled.
It was then time to locate the centres of the new 8.5mm tuner holes. This turned out to be harder than I initially thought due to the ridiculous locations of the original holes. With a little measuring, these were revealed to be unevenly spaced in the vertical, and badly placed with respect to both the centre line and the edges in the horizontal. The whole headstock is misshapen such that I can't have the new holes both equidistant from the edges and the centre-line. A choice was required - either situate the holes the same distance from the edge, or use the centre-line for reference. After an hour of indecision, I decided to drill horizontally equidistant from either edge, with the holes the same distance apart in the vertical.

Fuck, the original holes positions were ridiculous.
The resulting centres were not quite the same as the originals (ie each piece of dowel) but I reasoned that any offset should be hidden by the black headstock face and the rather large square backs of the Kluson tuners.  Finally, a little fiddling with the drill press got the new 8.5mm holes in and done.

The new holes fit the Kluson bushings just like a bought one!
With the new tuner holes completed (phew!), it was time to get on and cut the headstock shape. Using my usual Les Paul template (http://www.australianlespaulforums.com/download/Headstock.pdf) I traced, I cut with a scroll saw, and I sanded back with my flap wheels to finally arrive at a pretty good "open book" headstock shape.

Tracing the template
The completed headstock shape.
Awesome! Now the headstock can be finally sanded up through the grades ready for dye and finish. Now that I look at it, the curves on each side do look a little wonky, but I'm not sure what to do about it. With the tuners in place the irregularities may not be very noticeable me thinks. But then again, maybe a little time on the flap wheels could even out the curves a little. I'll ponder it once I start sanding and see how I feel. What I don't want to do is risk stuffing the whole thing up! Stay tuned.

Monday, 10 November 2014

Black Ash Telecaster: Moving the Bridge

Well, today I had every intention of getting the remainder of the hardware installed on the Black Ash Telecaster. But, unfortunately, it was not to be. When I did my mock build of the Telecaster prior to starting the finish, I did so with a humbucker in the neck position. As such, the bridge was positioned such that the strings travelled correctly over the poles of the humbucker and up the neck.

Now that I've decided to use a traditional Telecaster pickguard, it turns out the bridge was not perfectly placed to run parallel to the bottom edge of the guard (and wasn't centred either). It looked bloody horrible to tell you the truth. The only thing to do was to move the bridge, and that meant drilling out the original bridge screw holes and plugging them with 6mm oak dowel. Not the best thing to have to do once the finish is completed, but at least the bridge is large enough to cover the damage!


The job was, at least, completed with a minimum of fuss. I sanded the dowel a little with 180 grit paper to make it slide more easily into the 6mm hole, and used Titebond to glue each plug in place. Each plug required a tap with the hammer to get it all the way in, but in the end each sat nice and flush with the top of the guitar.

With the plugs in place, I was able to line up and install both the scratchplate and the control cover. All in all I reckon she's looking pretty bloody good - although in the photo below the bridge is just sitting on top of the plugs.


Once the Titebond has dried overnight, I'll get the bridge lined up again (using both the neck and pickguard as reference this time) and get it screwed down. Then I'll just have the wiring to go. Unfortunately I'm still waiting for shielding tape, so this may still be a while away.