Showing posts with label Setting the Neck. Show all posts
Showing posts with label Setting the Neck. Show all posts

Thursday, 8 January 2015

Ash Les Paul: Setting the Neck

Today I got back to the Ash Les Paul. I was able to level, re-crown and polish the frets for a sexy look and a super-smooth action! I've previously waited until after the neck was attached to do the frets, and on the whole my experiences have been mixed. Previously I have found it hard to re-crown frets on the bridge end of the neck for some models when the fretboard is close to the body. I decided to try leveling and re-crowning the frets before gluing this time. The frets turned out ok, but trying to hold on to the neck whilst sanding and filing was a bit of a bitch. I guess I need a couple of vices here on the work-bench!

Anyway, with the frets done, I carried on immediately and glued the neck. Fingers crossed that I did everything correctly! It all looks great - the E strings run nice and straight up the neck and are sitting almost on the top of the 22nd fret. Should make for a nice low action! However, in the back of my mind I couldn't shake a little voice telling me that I didn't use enough glue. I had all the surfaces covered, but there wasn't much squeeze out. But that's a good thing right?? Oh well, time will tell!

Titebond and a clamp does a set-neck make!
The whole shebang. She's looking the goods!
E strings sitting nice and straight up the neck and almost resting on the 22nd fret.
I'm very excited about getting this little baby completed, and she's actually starting to look like something now! Next step is to get the control cavity shielded and to solder on the ground wire. I don't think I'll shield the pickup cavities this time around as I've read comments out there on the inter-web saying that shielding here cuts the highs from the signal? Am I right in thinking this? Let me know your opinions out there!

Once the clamp comes off the neck, I'll be waxing the fretboard with Dingotone guitar wax and then starting on the electronics. Stay tuned!

Tuesday, 19 August 2014

Burley 335: Setting the Neck

With 7 coats of Tru-Oil on the front of the Burled 335, and the decision finally made to finish the guitar in an all-natural colour, I decided to get the neck on and glued as soon as possible. With 3 coats already on the back and sides, I could see how this guitar was going to look and I'm really digging it. With a natural Tru-Oil finish also planned for the neck, there was no reason to delay setting the neck. In fact, it seemed a better choice than waiting given that it will allow me to get a more even finish around the neck joint.



And so, without further ado, out came the clamp and the Titebond. The neck fit was still super-tight, but with a little coaxing (and clamping) the bugger was finally seated in the pocket and glued down tight.


A little cleanup with a wet-rag around the joint (I always use way too much Titebond) and everything was good to go. The great thing about set-neck kits that don't have the bridge pre-positioned is that you have the flexibility to get the neck glued without having to worry about whether it's centred with respect to the bridge or whether the strings are traveling nicely down it. That can all be fine-tuned when we drill the bridge posts.

Now all that is left for me to do is to  wait 24-48 hours for the joint to fully dry. After that it is back to the Tru-Oil!

Wednesday, 23 July 2014

Stone Roses Tribute: Setting the Neck

So the day finally arrived when this Stone Roses Tribute could start being assembled. The clear coats have been subjected to IR lamps for a few days and given I wont be polishing the surface to a shine, I'm pretty confident I can move on with the next steps. The first and most important task - gluing the set neck!

There was quite a bit of play in the neck of this kit, both in and out and laterally within the neck pocket. To make sure the neck was glued at the correct angle, I installed the bridge and tailpiece first along with the tuners. This allowed me to get the two E strings placed up the neck to check for correct lateral angle.

To make sure the neck was installed at the correct depth, I installed the neck pickup and made sure the neck wasn't so far into the pocket that it stopped the pickup from being installed. I marked pencil lines to indicate the exact depth required on each side of the neck to accomodate the pickup.

In terms of the neck angle front to back, putting the bridge at it's lowest height I was able to establish that the two E strings were touching the first few frets. This indicated that a good action could be dialed in without the need to shim the neck. Phew! With all this done, the neck could be glued into the correct place and clamped.




I used Titebond to glue the neck into the pocket (the king of wood glues) and now must wait two days for the glue to fully dry before putting any weight on it (ie. stringing it up!). I'm pretty happy with how the neck is sitting and can't wait to give this baby a strum!

Tuesday, 22 July 2014

Stone Roses Tribute: Video Build Diary #7

The seventh installment of my video build diary for the RC-1 Stone Roses Tribute is now on YouTube. This installment deals with the do-over of the Pollocking paint job, and (finally!) the setting of the neck.


Enjoy!